DIY 3D Printer Misc Parts

Having Trouble Ordering?

Please call: 800-734-3588 206-458-7550

Shipping Charges Too High?

We will refund your PayPal account.
Or you can for a correct PayPal invoice.

Ball End Allen Wrench Set, Long Arm Hex Key

Picture Coming

Sizes: 1.5mm, 2mm, 2.5mm, 3mm 4mm, 5mm

Hardened

Ballend

Long Arm

Plastic Carrier

$6.95

Thermal Fuse

192° C, 10 Amp Thermal Fuse

Thermal Fuse opens the 10 Amp circuit permanently if the temperature ever rises above 192° C

Safe for use up to 162° C

UL Rated: E117626

Bends should be 3 mm away from the body

A heat sink is required when soldering

The body is connected to a lead and may need to be isolated

1 / $1.50

RepRap, Mendel, Prusa 3D Printers
PCB Heatbed MK2 Hot Plate

With Soldered Resistor and LEDs

Compatible with: RepRap, Mendel, Prusa and other DIY 3D Printers

Dimension: 214 mm x 214 mm (8 3/8" x 8 3/8")

Includes a Thermistor

Resistor and LED already installed to indicate when power is applied

Power Input: 12Vdc or 24Vdc

Red Soldermask (both sides)

White Silkscreen (both sides)

Even Heat Distribution

$19.95

72 to 152 Watts
For 12 or 24 volt printers

We provide you a special option not normally found, a chance to pick the resistance (power level) you desire for your printer.

We have measured and sorted these MK2 hotbeds by their room temperature resistance which gives us a general idea of the wattage of each.

These MK2 Hotbeds can be used for both 12 and 24 volt systems. There are two heating circuits on each board. For 12 volt systems, you will run the heating elements in parallel, while 24v dc systems will be wired in series. Instructions are clearly marked on each board.

Which heatbed should I get?

We have heard of some customers having trouble with their printer when the heatbed turns on. Usually this is because the heat bed is using more power than the power supply can reliably provide.

If you have enough power, we would suggest the lower ohm heat beds, as they will heat up more quickly. If you have a less capable power supply, pick a heat bed that is well within its power specs.

On all of these beds, we like to use a heat spreader like a thin sheet of aluminum between the hotbed and the printing surface.

Lower Wattage

We've found that the lower wattage beds struggle to hold the higher temperatures. Insulating the bottom of the board, and possibly covering the unused sections of the top surface can help these boards heat up faster and hold temperature better, especially in the presence of a cooling fan.

Kossel Mini Aluminum Frame Extrusion Kit
	Silver colored. Made with clear anodized aluminum extrusions that capture an m3 nut. For use in Kossel system
Silver Colored Tolerance: -1 mm / +2 mm 1515 (15 mm x 15 mm) Clear Anodized Aluminum More information about the Kossel Extrusions.	1515 (9) 240 mm Sides (3) 600 mm Towers 4 mm slot No special expensive T nuts are required $49.95
	1515 Non-Standard Mini (9) 360 mm Sides (3) 600 mm Towers 4 mm slot No special expensive T nuts are required $49.95

Kossel Legacy Aluminum Frame Extrusion Kit
	Silver colored. Made with clear anodized aluminum extrusions that capture an m3 nut. No special expensive T nuts are required. For use in Kossel system
Silver Colored Tolerance: -1 mm / +2 mm 1515 (15 mm x 15 mm) Clear Anodized Aluminum	1515 Kossel Legacy (9) 360 mm Sides (3) 600 mm Towers 4 mm slot No special expensive T nuts are required $49.95

Silica Gel - Protect Your Filament
	Absorbes moisture from the air. Store your filament in an airtight container with Silica Gel to protect it. Environmentally friendly and economical. Reuse over and over. When the crystals turn dark, simply heat it in the oven with low heat to restore.
	450 gram Bag / $16.95 Protects up to 33 cubic feet 750 gram Can / $26.95 Protects up to 57 cubic feet

USB 2.0 A to Micro B Data Cable - 6 Feet
	$6.95

Spectra Line
	NOTE: May be in TWO PIECES
65 lb Yellow	20 yards, 65 Pound (Yellow) / $6.95
150 lb Yellow	10 yards, 150 Pound (Yellow) / $6.95

Black Techflex Spiral Wrap, Expandable Sleeving
Organize wires into neat bundles	Small 0.25", expands to 0.44" $2.95 / Meter Change quantity at Checkout
	Large 0.5", expands to 0.75" $3.95 / Meter Change quantity at Checkout