Phone Orders or Help: 800-734-3588, 206-458-7550 (Pacific Time)

Home > BOM > Prusa i3 Rework BOM

Bill of Materials (BOM) for Prusa i3 Rework 3D Printer

Having Trouble Ordering?

Please call: 800-734-3588 206-458-7550

Shipping Charges Too High?

We will refund your PayPal account.
Or you can for a correct PayPal invoice.

Parts We Have

Parts for Prusa i3 Rework 3D Printer

Qty

Source

Bill of Materials (BOM) for Prusa i3 Rework 3D Printer

Aluminum Frame

Single Frame

Heatbed Bed Mount

$99.95

BOM (Bill of Materials) for Prusa i3 Rework 3D Printer

Plastic Parts

0.30 mm layers

1 mm thick wallsl

All parts are PLA

High quality

Plastic parts may have burrs which need to be reemed out or lightly sanded.

$34 .95

Orange Blue or Black

GT2 Timing Belt

6 mm wide

2 mm pitch distance

Neoprene rubber with reinforced fiberglass

Two pieces

760 mm

900 mm

$4.25

GT2 Belt Drive Gear 20 Tooth 20T, 2 mm Pitch, 5 mm bore

We also have the 16 tooth belt drive gear.

3 / $6.95

NEMA 17 Stepper Motor XYZ

See Nema 17 Stepper Motor Diagram

High Torque: 5.5 kg-cm, 53.9 N-cm, 76 oz-in, 4.77 lb-in

4.2 Volt, 1.5 Amp, 1.8 deg per step

23 mm long, 5 mm Shaft with D Cut

Wires are 750 mm to the tip of the connector

Model: 42BYGH4803

2 Phase

200 Steps per Revolution

Resistance per Phase 2.8 Ohms

Inductance 4.8 mH

Class B Insulation

Kysan Electronics

5 / $80.00

Nuts, Bolts, Screws, Fasteners

Nuts - (33) m3

Nuts - (6) m4

Nuts - (2) m5

Nuts - (1) m8

Nuts - (34) m10

Nyloc Nuts - (1) m8

Washers - (53) 03 mm

Washers - (6) 08 mm

Washers - (34) 10 mm

Cap Screws - (41) m3 x 14

Cap Screws - (3) m3 x 24

Cap Screws - (4) m3 x 30

Cap Screws - (2) m3 x 60

Cap Screws - (6) m4 x 20

Hex Bolt - (1) m8 x 20

Set (Grub) Screws - (5) m3 x 8

Set (Grub) Screws - (1) m8 x 20

Silver Colored

$34.95

NOTE: We have nuts, bolts and screws in bulk.

Wade's Hobbed Bolt
With Nut and Washer

Picture Coming

$5.95

Bearings Kit
Made in China

Picture Coming

(1) MR624ZZ

(4) 608ZZG

(11) LM8UU

$12.50

Power Supply

24 Volt 400W Wei Hao Single Output Power Supply

Model: S-400-24

See specification.

$39.95

Mean Well Switching Power Supply

Model: S-350-12

See specification.

$39.95

Mean Well 150W Single Output with PFC Function

Model MW SP-150 15

See specification.

$39.95

J-Head Hot End

Original, Made by the Inventor

Not Chinese Knock-Off

For 1.75 filament. Includes:

5.6 Resistor with PTFE Tubes

100K Thermistor with PTFE Tubes
Thermistor specs

More information about the J Head Hot End and a video on How to Assemble a Hot End.

$59.95

(May be tan or black)

.35 mm, .4 mm, .5 mm

$59.95

Coupling 5*5

2 / $4.95

Fan - Quiet 40 mm Square

40 mm x 40 mm x 20mm Wide

12 Volts

Rated at 12.8 db

$9.95

Borosilicate Glass

200mm x 214mm

3 mm = $19.95
Imperfect* 3 mm = $12.95

* We have a few of the borosilicate glass which have either small nicks on the edge or minor scratches on the surface. These are guaranteed. If you are not happy with what you get, just

Aluminum Heat Spreader

200 mm x 214 mm

Picture Coming

Specifications:

6061 Aluminum
0.080" / 2.032 mm thick

Heatbed MK2 Hot Plate

With Soldered Resistor and LEDs

Compatible with: RepRap, Mendel, Prusa and other DIY 3D Printers

Dimension: 214 mm x 214 mm (8 3/8" x 8 3/8")

Includes a Thermistor

Resistor and LED already installed to indicate when power is applied

Power Input: 12Vdc or 24Vdc

Red Soldermask (both sides)

White Silkscreen (both sides)

Even Heat Distribution

$19.95

72 to 152 Watts
For 12 or 24 volt printers

We provide you a special option not normally found, a chance to pick the resistance (power level) you desire for your printer.

We have measured and sorted these MK2 hotbeds by their room temperature resistance which gives us a general idea of the wattage of each.

These MK2 Hotbeds can be used for both 12 and 24 volt systems. There are two heating circuits on each board. For 12 volt systems, you will run the heating elements in parallel, while 24v dc systems will be wired in series. Instructions are clearly marked on each board.

Which heatbed should I get?

We have heard of some customers having trouble with their printer when the heatbed turns on. Usually this is because the heat bed is using more power than the power supply can reliably provide.

If you have enough power, we would suggest the lower ohm heat beds, as they will heat up more quickly. If you have a less capable power supply, pick a heat bed that is well within its power specs.

On all of these beds, we like to use a heat spreader like a thin sheet of aluminum between the hotbed and the printing surface.

Lower Wattage

We've found that the lower wattage beds struggle to hold the higher temperatures. Insulating the bottom of the board, and possibly covering the unused sections of the top surface can help these boards heat up faster and hold temperature better, especially in the presence of a cooling fan.

Optional Parts

Optional Dampers

Steel and Rubber Dampers

Manufacturer's Part Number MY17RMDAMP

Significantly reduces noise, vibration and resonance problems commonly found in stepper motors

Robust but lightweight

Threaded mounting holes; can be mounted directly onto the motor flange

2.2 mm access hole, large enough to accommodate a spigot and gear or pulley

6 mm thick

Cork Dampers

Helps reduces noise, vibration and resonance problems commonly found in stepper motors

Helps prevent thermal transfer from motor to plastic parts

Mounting holes; can be mounted directly onto the motor flange

2.2 mm access hole, large enough to accommodate a spigot and gear or pulley

3 mm thick

NOTE: These dampers do not fit GEARED stepper motors

Steel and Rubber
5 / $36.50

Cork
5 / $6.95

Other quantities.

Kapton Tape

4" Wide

100' Length

11.95

3" High Quality Blue Tape

This high quality blue painter's tape is as good or better than the competitor's

Rated as 3". Its actual measurement is just over 2 3/4"

Roll = 60 yards

Can be cleanly removed for up to 21 days

11.95

Black Techflex Spiral Wrap, Expandable Sleeving

Organize wires into neat bundles

Small
0.25", expands to 0.44"

$2.95 / Meter
Change quantity at Checkout

Large
0.5", expands to 0.75"

$3.95 / Meter
Change quantity at Checkout

Split Loom to organize wires

Store / Organize Wires

Inside Diameter: 10 mm (~3/8")

3 Meters Long

Color: Black

3 meters / $5.95

1 meters / $1.95

Silica Gel - Protect Your Filament

Absorbes moisture from the air. Store your filament in an airtight container with Silica Gel to protect it.

Environmentally friendly and economical. Reuse over and over. When the crystals turn dark, simply heat it in the oven with low heat to restore.

450 gram Bag / $16.95
Protects up to 33 cubic feet

750 gram Can / $26.95
Protects up to 57 cubic feet

Parts We Do Not Have
Parts for Prusa i3 Rework 3D Printer	Qty
Smooth rod �8x320 mm	2
Smooth rod �8x350 mm	2
Smooth rod �8x370 mm	2
Threaded rod M5x300 mm	2
Threaded rod M10x210 mm	4
Threaded rod M10x380 mm	2
Springs	2
Binder Clips	4
Ramps	1
Atmega	1
Atepsticks	4
Endstops (with cables)	3